SUMMER BAG & PURSE

IMG_1438
Screen Shot 2016-02-05 at 15.45.55pattern available to buy from http://www.sewgirl.co.uk 

This is a pattern for a lovely matching lined hat, big beach bag and sunglasses case. Suitable for medium to heavyweight fabric such as cotton, denim, canvas or corduroy. Simple to make, the bag and purse have a magnetic clasp flap with button.

BAG MEASURES 43cm X 66cm (inc. handles)
SUNGLASSES CASE MEASURES 18cm x 12cm approx.

You will need:
BAG=1 metre of main fabric, 30cm of lining fabric, one magnetic clasp and one large (3cm) button.

PURSE= 25cm of main fabric, 25cm of lining fabric, 25cm of med weight fusible interfacing, one small magnetic clasp and one button.

Screen Shot 2016-02-05 at 16.47.33

HOW TO MAKE YOUR BIG BAG

CUTTING OUT THE PIECES
Cut out your bag pieces following the layout diagram.
You will need:
Two bag pieces A and B together in main fabric (cut one piece on folded fabric) lay the pattern piece as close to the end of the fabric as possible and make sure you have placed it so you have enough fabric leftover for the facing piece.
Trim down the dotted line on the pattern then cut two pieces of facing piece B in main fabric (see layout diag) ie cut one on folded fabric and two pieces of lower piece A in lining fabric.
Cut two flap pieces (one on folded fabric).

Screen Shot 2016-02-05 at 16.47.49

FLAPS
Firstly pin the flap pieces together RST, sew around with a 1cm seam allowance. Nick curves then turn inside out pushing out the edges with a knitting needle or chopstick.
Attach one side of your magnetic clasp to the flap so nick two little holes on one layer only at the marker point. Push the prongs of the clasp through then push together on the inside.

Screen Shot 2016-02-05 at 16.47.56

STITCH TOGETHER THE INNER LINING
With the RST pin together the lining piece A with the facing piece B then stitch a 1cm seam across. Repeat for other side. Top stitch on the RS.

Screen Shot 2016-02-05 at 16.48.04

Take one main bag piece pin the flap to the centre front top edge with the magnetic clasp facing up then tack stitch to secure in place, remove pins. (see pic).

Screen Shot 2016-02-05 at 16.48.19SEW UP THE SIDES
Now with the RST pin together the two main bag pieces at lower sides stitch a 1cm seam. Repeat for lining pieces but this time leave an opening in the lining for turning inside out.
Clip curved seams at corners.

Screen Shot 2016-02-05 at 16.48.36SEWING THE HANDLES
Turn the lining bag piece only inside out so the RS is visible.
Place one bag inside the other so the RST matching up all the raw edges of the handles on both sides, keep the flap tucked in between the bag and facing. Pin then stitch all around handles over the side seam then up and down the other side so your stitching finally ends where it began. Nick all curved seams and cut across corners (careful not to nick your stitching!). Turn your bag inside out through your opening.

Screen Shot 2016-02-05 at 16.48.47
Stitch the two front bag handles together with a square and a cross in the centre (see template).
Attach the other magnetic clasp in the bag front matching the position show as a X on the template.
Finally stitch up the opening in the lining.

There you have one great bag!

Now what about making a matching sunglasses case? ……..

CASECASE by Sewgirl

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s